EP brand alternative gearbox for woods rotary gearbox
NEW 40 HP GEARBOX Smooth Enter one 3/eight twelve spline output Interchangable with market place popular dimensions i.e.: OMNI GRIZZLEY CHEETAH HOWSE KING KUTTER BUSH HOG HICO SILVER EDGE A lot of A lot more
Functions
(1) brand new 45 horse power shearpin gearbox. This gearbox matches many various can make of 4′,5′ and some 6′ rotary cutters. I sell a whole lot of these bins each and every calendar year for many various applications and carry ALL Substitute Components for this box, but ideally you is not going to have to fear about that.
Right here are the specs on the box:
*45 horse energy gearbox
*Common one-3/8″ smooth input shaft(in which the pto shaft hooks on). The pto shaft is held on by a one/two shearbolt.
*length of the input shaft out of the gearbox is 3″ long
*bolt hole sample for mounting is on the corners, four-three/4 centre of gap to centre of hole. It takes a five/8″ bolt.
*twelve splined output shaft(in which the blade carrier hooks up on the bottom)
*one-9/16 outside the house measurement over the output shaft splines- from the base of the output cap to the end of the splines is 2-three/four” long- all round duration of the output shaft is 4-one/2″ prolonged.
*normally takes a 1″ threaded castle nut and a carter key on the bottom of the output shaft to protected blade pan(NUT is integrated – – BLADE PAN IS NOT!!)
*overall top of the box from the top of the mower deck to the best of the box is nine-one/two”
This is a reasonably heavy merchandise (forty seven lbs.) so freight is not low cost, but we do not make everything off of freight, whatsoever ups costs us we demand you.
40 HP
one:one:forty seven Ratio
one-3/8″ Easy Input Shaft with Shear Pin Hole
1-one/2″ twelve-Spline Ouput Shaft
Bolt Sample: six-1/2″ (4) 5/eight” Holes, 5″ 
Centre Gap Needed for Shaft Assembly
The Input and Output Shafts Can not be Purchased Serparately.
They are Offered as a package.
The package includes the subsequent parts: enter shaft, input equipment, output shaft, output equipment.
The Shaft Kit Cannot Be Separated.
EP brand replacement gearbox for woods rotary gearbox
Rotary Cutter Gearbox Troubleshooting Guidebook
Is your mower leaking, creaking or otherwise carrying out incorrectly? You have appear to the appropriate location.
Read through under for the most frequent troubles with rotary cutter gearboxes and their solutions (from fast and filthy, to skilled).
Leaking Base Seal:
If you’ve wrapped some baling or fencing wire around your output shaft and blown the seal, the specialist issue to do is to change the seal.
If your output seal is intact, and you are ready to get ID, OD and thickness measurements (in millimeters), most bearing residences can order you up a generic double-lip seal that will get you again up-and-operating. If not, give us a get in touch with and we can aid you type out what you want.
A dental pick is the simplest way to eliminate the old seal prior to pressing in the new a single.
If you happen to be blessed adequate to have a slow-leak, the fast and dirty strategy is to operate automotive-sort grease in the gearbox right up until the new seal arrives in. Be positive to check out and insert grease much more regularly than you would with oil, as this is NOT a professional repair.
Damaged Output Shaft:
Uh oh. You strike something that failed to move. The excellent news is that the output shaft on most gearboxes is pretty effortless to change. The negative information is… it truly is hardly ever an isolated failure.
The first point to do is to just take apart your gearbox and evaluate the full extent of the injury. If it is actually just the output shaft, you need to be ready to change it out, no difficulty. The output shafts commence at about $70 and go up in price depending on the dimensions of the gearbox.
Even so, in most cases, the bearings ($20/ea), seals ($10/ea) and equipment-established ($70) will also typically get a beating. If you might be unlucky, the output cap ($eighty) will also experience some damage.
In this scenario, it is typically less costly to substitute the gearbox. Assess the value of parts to the expense of an entire, new, warrantied gearbox. Sometimes, even pros have to know when to get in touch with it a day.
I Want to Adjust my Enter Shaft:
If you are drained of changing shear pins or hunting again and observing that your mower has not been cutting, you may want to set up a slip-clutch pto shaft (Yes, we promote people as well).
This normally requires setting up a 540-design, six-spline enter shaft ($eighty five) on your mower’s gearbox.
Fortunate for you, we did a write-up on our weblog. It is known as “How to modify the enter shaft on your rotary cutter gearbox”.
My Gearbox is Groaning/Creaking:
“Groaning”, “creaking”, or “popping” all seem type-of comparable more than-the-mobile phone. The greatest thing to do is to disassemble your gearbox and consider a look at the gears and bearings. The issue will typically existing by itself in the way of broken/missing gear teeth, toasted gears (like that photo on our property webpage), or blown bearings.
If almost everything appears standard, try out changing the gear-mesh. This is done with the mylar “gaskets” that sit amongst the primary gearbox circumstance and the enter/output caps. Try adding or taking away some of these spacers till your gears have roughly one/8″-1/4″ of free enjoy. Specialists can order replacements ($one-two) in varying thicknesses, but we advise the quick and filthy strategy of reducing your own out of a sheet of mylar.
Don’t fail to remember to re-seal the gearbox with RTV following you’ve identified the correct blend. Even even though they are named “gaskets”, they is not going to seal your gearbox on their own.
Much more information on Agricultural Gearbox awaits you! Browse through https://agricultural-gearbox.xyz/agricultural-gearbox/index.html for more!