The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for employ with split-tapered sprockets and pulleys of the same bushing style. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and will be purchased on the same page as the pulley you will need. For work with with 5/8” shaft sizes. Includes set screws. More Features: Made of Steel For employ with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque ability from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and gear belt pulleys. The split tapered bushing alleviates the need to have an element bored to size, preferably lowering on hand requirements and enabling improvements in shaft size if necessary. The barrel of the split tapered bushing is normally split in two areas and is definitely keyed to the shaft. The barrel OD is also keyed to the drive component aswell. The advantage of the split tapered bushing is it will hold, whether or not the fasteners turn into loose. Split tapered bushings are interchangeable between manufacturers.

Taper bushing are trusted as well as sprockets, v-belt pulleys, timing pulleys, coupling and other mechanical parts with taper bore connections.
Taper bushing series are constructed with high quality engineered supplies with superb tolerance. The characteristic is easy to use and needs no further alteration. These bushings can go well with almost all sorts of assemblies and sizes. They are the best choice in design for mechanical connections.
To complete designations put bore size. For instance: PD1215X16MM designates a 1215 taper bushing with a 16mm bore.
No costly re-boring: total range of both metric and imperial available.
Standard range matches up to 125mm/5″ shafts & Hub diameter required depends upon the application.
Complete brief reach range available, for compact light in weight assemblies & Clean, Compact Style.
Ease of installation and removal.
This Split Taper Bushing is designed exclusively for use with cast iron bushed bore pulleys and can be purchased on a single page as the pulley you will need.
For use with 1 3/16” shaft sizes.
Includes 2 set screws.

Additional Features:
Made of Steel
For use with cast iron bushed bore pulley
This U1 Bushing with 5-1/2″ bore is a high-quality precision product that’s built for strength and strength. U1 bushings are used in an extensively broad range of applications, including; sprockets, shaves, pulleys, gears, plus much more, we as well offer all of these products. What sets this bushing apart is the high-quality steel building along with exact manufacturing and top quality control; this ensures that you always get yourself a premium quality regular product. What really models us in addition to the other folks is our highly trained expert workers and our company-wide aim of customer satisfaction.
1. Be certain the tapered cone surfaces of the bushing and the within of the driven item happen to be clean and free of anti-seize lubricants.
2. Place the bushing in sprocket or various other portion type that accepts the bushing.
3. Place cap screws loosely in pull-up holes. The bushing continues to be loose to make sure sliding match on shaft.
4. With crucial on shaft, slide the sprocket or other component type to the desired situation on the shaft. Be sure to leave the heads of the cap screws accessible.
5. Align the sprocket or portion type, tighten the screws alternatively and progressively until they are pulled up tight. Do not employ extensions on the wrench handles and don’t allow the sprocket or portion to be drawn i connection with flange of bushing. At this time there should be a gap between the bushing flange and sprocket, make certain this gap does not close.
Dual split barrel ensures concentricity
Grips the shaft with great clamp fit
High torque carrying capacity
Permits blind assembly
Load not carried or tied to mounting screws
External key on most sizes for great drive and higher torque carrying capabilities
Double-split barrel for positive clamping
Solid flange to keep up concentric bores
Available in inches, metric, and spline bores. Bore range between 3/8″ to 10″
Solid Flange & Dual Split Barrel – Assures better concentricity to the shaft.
Key to Key Drive – With keys upon both the shaft and product to supply the strongest possible drive.
3/4″ per Foot Taper on Barrel – Self locking taper provides the highest amount of mechanical locking item to product.
The tapered barrel on these bushings is split on both sides, allowing them to contract more tightly around the shaft than quick-disconnect and taper-lock bushings. They’re for employ with split-tapered sprockets and pulleys of the same bushing design. As you tighten the included screws, the bushing grips the shaft and pulls it in to the sprocket or pulley.
This Split Taper Bushing was created exclusively for use with cast iron bushed bore pulleys and will be purchased on the same page as the pulley you will need. For use with 5/8” shaft sizes. Includes set screws. More Features: Made of Steel For make use of with cast iron bushed bore pulley
Our stock metal Split Taper bushings feature wrench torque potential from 95 to 3,000 pounds and bore sizes from 3/8″ to 6-3/16″.
The split tapered bushing is a flanged bushing. Split tapered bushings are used on sheaves, pulleys, sprockets and equipment belt pulleys. The split tapered bushing alleviates the need to have a component bored to size, preferably lowering readily available requirements and enabling improvements in shaft size if important. The barrel of the split tapered bushing is normally split in two locations and is definitely keyed to the shaft. The barrel OD can be keyed to the drive component as well. The benefit of the split tapered bushing could it be will hold, regardless if the fasteners turn into loose. Split tapered bushings will be interchangeable between manufacturers.